Among the new energy vehicles (pure electric as an example) high voltage cable assemblies can be divided into 5 parts 1. Power battery high voltage cable: that is, the wiring bundle between the power battery and the high voltage box. 2. Motor controller cable: that is, the cable connecting the high voltage box to the motor controller. 3. Fast charging wire harness: connect the cable assembly ...
I. Ultrasonic welding principle: Ultrasonic wiring harness welding is a commonly used process of car wire welding. The principle is to re -combine the surface of the welding material through high frequency vibration. Ultrasonic welding energy consumption is low, no pollution, strong welding and low internal resistance, and does not change the chemical properties of welding parts. Welding cond...
1. Substrate requirements: No dirt Grease/oil free Dry During use, the following products cannot be used: Talcum powder Silicone Molding agent hand cream 2. When the tape is pulled from the tape roll: Do not store the tape in the way shown below. Do not touch the end of the tape with your fingers (with oil)! 3. The spool of tape is rolled close to the wire harness, and the tape cannot...
HV Cable selection 1. Cable diameter According to the layout diagram of each high-voltage electrical component of the vehicle, the main circuit and branch circuit are distinguished, and the responsible characteristics of the high-voltage components connected to the high-voltage wiring harness are determined. Characteristics include working voltage, rated power, peak power, rated current, peak curr...
The European electric vehicle charging standard CCS2 is a combined standard that integrates AC charging and DC charging. The combined charging system is an open international standardized system, mainly promoted by Audi, BMW, Chrysler, Daimler, Ford, General Motors, Porsche and Volkswagen. Vehicles exported to Europe need to meet their physical interface and communication requirements. Euro...
The charging system can be divided into two methods: conventional charging and fast charging. From the perspective of appearance and size, the difference between the charging ports is actually very simple. The fast charging port is large and has 9 holes (two large holes, one middle hole, and 6 small holes). The slow charging port is small and has 7 holes (5 large holes and 2 small holes), so that ...
Connectors are used in every car. The device uses signals such as electricity and light to control the corresponding mechanical force to connect, disconnect, and convert, and then realizes a functional element of the corresponding circuit or optical channel conversion, and With the help of ECT electrical and optical signals, signal distortion and corresponding energy loss can be effectively preven...
When consumers are looking to purchase an EV, the time it takes to charge an EV continues to influence their purchasing decision. Today, the fastest way to charge an electric vehicle is high-power direct current (DC) fast charging. DC fast charging, unlike AC charging, requires specific OEM considerations when designing critical components of the vehicle's electrical architecture, such as charging...
The composition of the automotive energy storage power supply wiring harness is composed of wires and connectors of different specifications and performances. The main specifications and performance requirements are as follows: 01) Cross-sectional area of energy storage wiring harness According to the load and current of the electrical equipment, select the cross-sectional area of th...
With the increase of automotive electrical equipment, the electrical functions and functional configuration of the vehicle are becoming more and more complex, and the requirements for the rationality and optimal design of the wire harness are gradually increasing. At the same time, under the trend of gradually decreasing vehicle cost, the cost pressure of wire harness is also gradually increasing....
Anderson plug wire harness is mainly used for UPS power supply, 5G power supply, charger/pile, cleaning equipment, lithium battery, AGV intelligent carrier. So, what are the main types and characteristics of Anderson plug wiring harnesses? What should we pay attention to in the daily use process? Product category: 1, single-pole Anderson plug power harness: rated current 5A, 10A, 15A, 20A, 30A, 40...
Advantages of energy storage harness compared to other energy storage devices? It is predicted that by 2027, the energy storage harness market will reach $27.5 billion. As a new energy storage device in the field of energy storage and conversion, energy storage harness has attracted market attention, and the application field is constantly expanding, and the future market development prospe...
once you subscribe our newsletter. we will keep you posted the latest catalog,Also will inform you the trendy news for the electronics and wire harness.